Structural polyester resins

Structural polyester resins

Contact:

elzbieta.andrzejczak@chemikolor.pl
tel.: 607-373-564; tel.:519-848-620

agnieszka.dajwlowska@chemikolor.pl
tel.: 693-414-477; tel.: 519-848-603

ESTROMAL 11 LM - 02

Orthophtalic resin, reactive, thixotropic, fast, easy to vent out and reduced emission of styrene. It is mainly used for the production of GRP (glass-reinforced polyester laminates).

ESTROMAL DL 145-2

Average reactive resin constituting the styrene solution of unsaturated polyester type DCPD-TPA, thixotropic, pre-accelerated, easily vent to the reduced styrene emission during the production and after. It is mainly used for the production of GRP (glass-reinforced polyester laminates).

PALATAL A 400-01

Resin based on isophthalic acid and standard glycol dissolved in styrene, highly reactive, medium viscous. It is intended for the production of glass fiber reinforced and resistant to hydrolysis and low water absorption.

PALATAL U 541 TV-03

Structural resin, orthophtalic, accelerated, low styrene emission, thixotropic, with excellent processing characteristics. It has a cure rate of the colour system. It is used for the production of GRP (glass-reinforced polyester laminates) by hand or spray.

POLIMAL 100-65 APy Orthophtalic resin, structural, rigid, with excellent processing characteristics (performance in lamination), accelerated, with reduced emissions of styrene. It has a colour index of cure. Recommended for the production of GRP (glass-reinforced polyester laminates)by hand or spray.
POLIMAL 101 Orthophtalic resin, design, quite flexible, with good strength (high impact). It is mainly used for the production of cartridges mining, cements and fillers, and laminates.
POLIMAL 103

Orthophtalic resin, design, quite flexible, average reactive, low viscosity, with good strength. It is mainly used for the production of GRP (glass-reinforced polyester laminates), by hand.

POLIMAL 108

Orthophtalic resin, structural, rigid, average reactive, low viscosity, paraffin wax (which gives a non-viscous surface finished products). Is mainly used as a finishing layer of glass-fiber laminate, and as one of the components of floor screeds.

POLIMAL 109

Orthophtalic resin, structural, rigid and high hardness after hardening, average reactive. It is mainly used for the production of GRP (glass-reinforced polyester laminates) especially large size, rigid, by manual method.

POLIMAL 109-34 APy

Orthophtalic resin, construction, accelerated, average reactive, low viscosity, with good mechanical properties, reduced emission of styrene. It is used for the production of GRP (glass-reinforced polyester laminates), especially large size, rigid, by manual method.

POLIMAL 109-34 Py

Orthophtalic resin, construction, accelerated, average reactive, low viscosity, with excellent processing characteristics. It is mainly used for the production of GRP (glass-reinforced polyester laminates), especially large size, rigid, by manual method.

POLIMAL 1053

Structural resin, medium-elastic, with very good processing characteristics, very good strength and high thermal resistance. It is used for the production of GRP (glass-reinforced polyester laminates) and resin-mineral castings

POLIMAL 1056

Structural resin, rigid, with very good processing characteristics, very good strength and high thermal resistance. It is used for the production of GRP (glass-reinforced polyester laminates) and resin-mineral castings

POLYLITE 440-M850

Orthophtalic resin, average reactive, thixotropic, accelerated, with reduced emissions of styrene. It is used for the production of GRP (glass-reinforced polyester laminates) by manual or spray method.

POLYLITE 440-M888

Orthophtalic resin, average reactive, thixotropic, accelerated, with reduced emissions of styrene, with excellent processing properties. Contains an additive that causes the cured laminate is not sticky surface. It is used for the production of GRP (glass-reinforced polyester laminates) by manual or spray method.

Special polyester resins

POLYLITE 415-041

Orthophtalic resin, medium reactive, not accelerated, not thixotropic, high heat deflection temperature combined with high tensile elongation. It was specially developed for polyester concrete, is also suitable for injection forming of the resin and forming at low pressure.
ESTROMAL A-023

Orthophtalic resin, medium reactive, available in regular and organic version (marked Eco). It is mainly used for the production of mineral filled goods (artificial marble).

ESTROMAL 11 DC-06

The resin used to produce a spatula.

POLIMAL 109-32 RPyK

Orthophtalic resin, double accelerated. Insensitive to low processing temperature and less sensitive to moisture. Recommended for the production of marble-goods (window sills, countertops, panels, etc..) produced by casting with mineral fillers (eg. Dolomite flour, silica flour, etc.) and for the production of rigid laminates

POLIMAL 109-32 K

Orthophtalic resin, neutral. This gives a tack free surface after curing. Recommended for the production of marble-goods (window sills, countertops, panels, etc..) produced by casting with mineral fillers (eg. dolomite flour, silica flour, etc.) and for the production of rigid laminates.

ESTROMAL 103 E

Orthophtalic resin, construction, with an average stiffness and increased flexibility. It is mainly used in haberdashery industry for the production of plates and Estral type discs.

POLIMAL 103 G

Orthophtalic resin, transparent, medium reactive, low viscosity, with good processing characteristics. It is used in the haberdashery industry (production of buttons), and to cast transparent.

POLIMAL 103 GL

Orthophtalic resin, transparent, medium reactive, highly viscous, with good processing characteristics. It is used in the haberdashery industry (production of buttons), and to cast transparent.

ESTROMAL 1454

Terephthalic resin, medium reactive. It is mainly used for the production of mineral fillers (ornamental figures) and GRP (glass-reinforced polyester laminates).

ESTROMAL 1456 Terephthalic resign. It is used mainly for the production of mineral fillers and fiberglass. Products from this resin have very high mechanical strength, technical, and increased chemical resistance. Offered resin is used for the production of decorative figures, window sills. Assume a large amount of filler.
POLIMAL 101-34 BPy

Orthophtalic resin, accelerated with an amine, with good processing characteristics (high yield in relation to a mineral filler) and short gelation time. It is used for the production of castings and garden figures (gnomes, dummies, etc.).

POLIMAL 144-01

Resin with high heat resistance HDT, neutral, efficient. It has a short gelation time. It is used for the production of garden figures (gnomes, dummies, etc.).

POLIMAL 101-36 B

Orthophtalic resin, standard, accelerated with an amine, with high durability. It is used mainly as an ingredient in the production of cements and fillers.

POLIMAL 109-39

Orthophtalic resin, structural, rigid, high durability of the DMA (with amines). It is used mainly as an ingredient in the production of cements and fillers.

POLIMAL 160

Orthophtalic resin, flame retardant, medium reactive, medium viscous. With the addition of flame retardants (eg. 5-10% antimony trioxide) is non-flammable. It is used for the production of polyester-glass laminates, flame retardant.

POLIMAL 1602 APyS

Self-extinguishing resin, filled, fast, high heat resistance HDT> 100°C, with good processing characteristics. It is used for the production of glass reinforced polyester flame retardant (power box).

POLIMAL 1608 PS

Accelerated construction resin DCPD-based flame retardant and smoke emissions. It is intended for the production of glass reinforced polyester flame retardant and of smoke.

DION 800 M 750

Self-extinguishing resin, construction, orthophtalic, accelerated, thixotropic, with reduced emissions of styrene. Contains chlorinated paraffin and antimony trioxide. It is used for the production of polyester-glass laminates with reduced flammability by hand or spray.

POLYLITE 410-900

Orthophtalic resin, thixotropic, accelerated, with very high heat deflection temperature (HDT). Suitable for hand and spray lamination. It is used for molds/forms.

POLYLITE 33542-75

The resin with the filler and an accelerator for the production of forms. Suitable GRP lamination structure.

POLIMAL 142

Terephthalic resin, highly viscous, with a high thermal resistance. It is mainly used for the production of molding

Flexible, polyester resins

POLIMAL 150

Orthophtalic resin, flexible, law reactive, with a relatively low polymerization shrinkage. Is mainly used as an additive to resins toughened rigid construction, to increase flexibility in fiberglass and achieve greater impact strength and elongation at break.

Chemical resistant polyester resins

ESTROMAL 14 PB-06

Terephthalic resin, highly reactive, with improved properties, chemical resistance and high strength. It is used mainly for the production of polymer, also fiberglass.

POLIMAL 138

Bisphenol resin, medium reactive, low viscosity, with improved resistance to alkalis and heat resistance (with good processing parameters). It is used for the production of chemically resistant GRP (glass reinforced polyester).

POLIMAL VE -2MM

Vinyl ester resin, very good processing characteristics, thermal resistance and, above all, excellent chemical resistance to a very wide range. It is used for the production of chemical resistant polyester-glass laminates, mold, chemical resistant polymer concrete and others.

POLIMAL VE- 6MM

Engineering resin, vinyl ester, modified neutral. It is characterized by an increased resistance to chemicals, heat, good processability characteristics, good saturate of fiberglass. After curing, a dry surface is obtained. The resin is suitable for the production of polyester-glass laminates and carpet. It has a Certificate of National Institute of Hygiene.

Contact:


elzbieta.andrzejczak@chemikolor.pl
tel.: 607-373-564
tel.:519-848-620

agnieszka.dajwlowska@chemikolor.pl
tel.: 693-414-477
tel.: 519-848-603